Konica minolta bizhub c227 error c9401



Konica minolta bizhub c227 error c9401

Шаг 1
Откройте переднюю крышку.

Шаг 2
Извлеките ёмкость для отработанного тонера и цветные фотобарабаны.

Шаг 3
Проверьте целостность и равномерность магнитной кисти блоков проявки.

Шаг 4
Проверьте корректность установки фотобарабанов.

Шаг 1
Выключите главный выключатель.

Шаг 2
В зависимости от модели нажмите кнопку стоп или кнопку reset (желтая кнопка), и, удерживая её, включите главный выключатель аппарата.

Шаг 3
При появлении на экране кнопки trouble reset, нажмите её.

Шаг 4
Выключите и через 10 секунд включите главный выключатель аппарата.

Шаг 5
Если ошибка не сбросилась, требуется диагностика цепи узла фиксации.

Шаг 1
Войдите в сервисный режим по процедуре сброса ошибок узла фиксации.

Шаг 2
В режиме System settings переустановите значение программного переключателя 03-1 в состояние выключено (0).

Шаг 3
Выйдите из сервисного режима и перезапустите систему.

Шаг 4
При повторном возникновении ошибки требуется диагностика цепей узла фиксации.

Шаг 1
Проверьте ресурсы работы основных расходных материалов (фотобарабан, узел проявки, лента переноса) используя меню «Утилиты» или веб-интерфейс. В случае превышения ресурса замените, ресурс которого превышен.

Шаг 2
Если счетчики расходных материалов не превышены, выполните режим «Стабилизации», используя меню «Утилиты». Настройки администратора — настройки системы — настройки специалиста — регулировка принтера — стабилизация, инициализация + стабилизация.

Шаг 3
Если пункт 2 не дал положительного результата, выполните очистку коротронов заряда. Для этого откройте переднюю крышку аппарата и при помощи шомпола очистите коротрон заряда.

Источник

мфу konica minolta bizhub c227/284 Сервисный режим Service mode

Новый аппарат (запуск нового аппарата…) полосит как тетрадь в клетку , то голубые то пурпурные полосы при копировании, сканировании.

The new device (launching a new device …) stripes like a notebook into a cell, then blue or purple stripes when copying, scanning.

инструкция по установке без гарантии installation manual bizhub installation manual bizhub
http://sf.uploads.ru/J3DVn.pdf

Вход в сервисный режим Service mode
1. Нажмите на панели кнопку Menu.
2. На дисплее нажмите Counter.
3. Далее с клавиатурной панели введите «Stop 00 Stop 01»
4. Введите пароль CE (сервис инженера), по умолчанию: 9272927292729272

мануал Настройки в сервеснмо режиме
13. Date & Time Setting/Time Zone Setting (Service Mode)
(1) Display the Service Mode screen. (For details of how to display the Service Mode screen, see the service manual.)
(2) Display the Date & Time Setting/Time Zone Setting screen. (To display the Date & Time Setting/Time Zone Setting screen, press Stop → 3 on the control panel.)
(3) Do not input date and time but touch “Entry” of the Date & Time Setting.
(4) Input the time zone using up/down keys or direct keys.
(5) Touch “Entry” of the Time Zone Setting.
(6) Touch “Apply.”
(7) Touch “OK.”
(8) Touch “Next.”
14. Serial number input Note: Serial number input is, if necessary, needed only for the optional devices installed in “9. Installing other options.”
(1) Touch the item you want to enter and input the serial number.
(2) Touch “END.”
(3) For other devices, enter their serial number in the same way.
(4) Touch “END.” (5) Touch “Next.”
15. Unit change Note: This function allows the user to select the type of message that will appear when the replacement time arrives for each of the different units.
(1) Select the appropriate message type for each unit.
(2) Touch “Service.”

16. Performing Non-Image Area Erase Check Note: Perform the below at the site where customer uses the machine.
(1) Select the Non-Image Area Erase Check function as follows: Machine → Non-Image Area Erase Check.
(2) Open fully the reverse automatic document feeder or the original cover if loaded. Note:
• Do NOT place a document on the document glass. • Clean the document glass if dirty.
(3) Press the Start key.
(4) Make sure that “Result” is “OK.” Note: If “Result” is “NG1” or “NG2”, review the place and direction of installation, or take measures to block the light source (by covering it, etc.), then perform installation checking again. (If a fluorescent light or other bright light sources exist right above the machine, the light source can hinder installation checking and cause operation errors in the Non-Image Area Erase Check. For detailed information, see the service manual.)
(5) Touch “OK.
17. Configuring other options
(1) If any of the following options are installed, refer to the “Configuration procedures” of the installation manual for each option and configure the option(s).
Reverse Automatic Document Feeder DF-628

Пароль администратора Konica Minolta

Стандартные пароли для администрирования систем bizhub:

для моделей bizhub 162, 163, 215 — 000000
для Web-интерфейса — sysadm

для моделей bizhub 250 — 00000000
для Web-интерфейса — 00000000

для моделей bizhub (C) 223, 283 — 12345678
для Web-интерфейса — 12345678

для моделей bizhub (C) 224, 284 — 1234567812345678
для Web-интерфейса — 1234567812345678

мфу konica minolta bizhub c227/284 Сервисный режим Service mode : 6 комментариев

bizhub C287 Series 28C-8 Series MFP firmware GC2-R9 GC3-R9 A7970Y0-F000-GC3-R9-990-CHECKSUM-2eca.ZIP mkMSGx.bat
(en, de, fr, it, nl)
* mkMSG1.bat (english, german, french, italian, dutch)
* mkMSG2.bat (english, danish, swedish, norwegian, finnish)
* mkMSG3.bat (english, greek, turkish, russian)
* mkMSG4.bat (english, czech, polish, slovak, romanian)
* mkMSG5.bat (english, spanish, portuguese, catalan, basque)
* mkMSG6.bat (english, german, slovenian)
* mkMSG7.bat (english, spanish, portuguese, hungarian)

Rom Version
MFP Card Version A7970Y0-F000-G00-R9
MFP Controller BOOT Program A7970Y0-1E00-G00-05
MFP Controller Linux Base Linux-3.10.40
MFP Controller Kernel Program A7970Y0-1C00-G00-92
MFP Controller SubSet A7970Y0-1F00-G00-R1
MFP Controller A7970Y0-0100-G00-R9
MFP Controller System A7970Y0-1000-G00-R9
MFP Controller Print Controller A7970Y0-3000-G00-R2
MFP Controller Print Controller Font A7970Y0-3F00-G00-R0
MFP Controller Print Controller Demo Page A7970Y0-3E00-G00-00
Image Reader Controller A7970Y0-8600-G00-C9
MFP Controller MIO A7970Y0-5000-G02-B7
Operation Panel Message Data A7970Y0-8100-G00-R4
MFP Controller PIC A7970Y0-8200-G00-F0
MFP Controller PIC Image Parameter A7970Y0-8A01-G00-01
MFP Controller Thread Image Parameter A7970Y0-8B01-G00-03
MFP Controller IR Image Parameter A7970Y0-8C01-G00-15
Finisher
Machine Controller A7970Y0-0200-G00-30
Machine Controller BOOT A7970Y0-0210-G00-00
Machine Controller Printer A7970Y0-0220-G00-27
Machine Controller Media A7970Y0-0230-G00-01
Machine Controller IO A7970Y0-0240-G00-00
Machine Controller Scanner A7970Y0-0300-G00-05
ADF A7V70Y0-0024-G00-35
Fax Board Controller1
Fax Board Controller2
Fax Board Controller3
Fax Board Controller4
SD
DSC1
DSC2
Panel CPU A7AH0Y0-8900-G20-04
SCB A7AH0Y0-1A00-G00-05
Power Sub-CPU A7AH0Y0-1900-G00-81
SATA Controller A7AH0Y0-6401-G00-04
Integrated Printer Driver Version 5-4.1b-0-G00-09
Movie Data
Voice Data
Dictionary Data
OCR Library
Authentication Customize Data
Panel Sound Data
Loadable Device Driver1
Loadable Device Driver2

Привет! У меня вопрос по МФУ Bizhub 308e. Я хотел настроить на нём функцию Защищённой печати ( чтобы каждый мог по коду распечатать свой документ). Прикрепил к письму файлы того как я отправляю на печать.
Документ приходит на МФУ в список заданий, и я его не могу распечатать,
пишет на дисплее — Результат Ошибка удаления
Ошибка получения Переполнение памяти.

Как можно Это устранить. Если нужно очистить память — то как это можно сделать? И можно ли это сделать чтобы не удалились настройки?

Как поменять дату на притнтере коника минолта с 227? В настройка не могу найти

Зайти Через веб интерфейс устройства, к примеру https://192.168.1.50 под Administrator начальный пароль 1234567812345678. Выбрать select [Maintenance] — [Date/Time Setting] — [Manual Setting] , then configure the following settings Ручная установка даты времени часового пояса. Automatically configuring settings using NTP (Протокол синхронизации времени) указать адрес сервера для синхронизации времени
Официальный мануал с картинками
https://manuals.konicaminolta.eu/bizhub-C554-C454-C364-C284-C224/EN/contents/id08-0037.html

Здравствуйте. Подскажите, пожалуста, как устранить полосы на цветной печати Bizhub227? Проверяли все настройки, вроде, в норме. Покупался с рук. У предыдущих хозяев небыло ни каких проблем.
Все меню на английском, нет в нем русских настроек. Что делать подскажите, пожалуста

Полосы при копировании он Всегда работает +5 Часовой Регион

Источник

Error Code List

LAN (IEEE802.1X)

Connection has already been established.

Unable to find the destination AP (SSID).

Negotiation of the EAP method failed.

The EAP authentication failed (user ID, password, certificate, etc.)

Verification error of the server certificate (EAP-TLS/EAP-TTLS/PEAP).

Negotiation of the phase 2 method failed (PEAP).

Response from the server has timed out.

Failed to start the supplicant task.

The server certificate has expired (EAP-TLS/EAP-TTLS/PEAP).

CA verification error of the server certificate (EAP-TLS/EAP-TTLS/PEAP).

Server ID verification error of the server certificate (EAP-TLS/EAP-TTLS/PEAP).

Settings are combined normally.

Connection and authentication are complete.

Incorrect format of the server certificate (EAP-TLS/EAP-TTLS/PEAP).

The hard disk path is not specified for the certificate verification (PKI) function (EAP-TLS/EAP-TTLS/PEAP).

The certificate verification (PKI) function is in the excessive multiplex processing status (EAP-TLS/EAP-TTLS/PEAP).

Parameter error of the certificate (EAP-TLS/EAP-TTLS/PEAP).

Internal error of the certificate verification (PKI) function (EAP-TLS/EAP-TTLS/PEAP).

An invalid operation occurred.

A protocol error occurred.

The time limit is exceeded.

Читайте также:  Что означает error 403 forbidden

The number of search results has exceeded the maximum number of items allowed.

The comparison result is FALSE.

The comparison result is TRUE.

The LDAP server does not support SASL.

Strong authentication is required.

Unable to trace the link although Referral is specified.

Administration limit on the server has exceeded.

Critical extension is unavailable.

Confidentiality is required.

Intermediary bind result for multi-stage binds

Requested attribute does not exist.

The type is not defined.

An inappropriate matching occurred.

A constraint violation occurred.

The attribute exists or the value has been assigned.

The syntax is invalid.

Cannot find the search route.

The alias is invalid.

The syntax of DN is invalid.

This object is a terminal (leaf).

Cannot de-reference the alias.

Authentication is inappropriate.

Failed to log in to the LDAP server.

The user has insufficient access rights.

The server is busy.

The server is unavailable.

The server does not handle directory requests.

The chain of referrals has looped back to a referring server.

There was a naming violation.

There was an object class violation.

Operation is not allowed on a non-leaf object.

Operation is not allowed on RDN.

The object already exists.

Cannot modify object class.

Results returned are too large.

Multiple directory service agents (DSA) are affected.

An unexpected error occurred.

Unable to connect to the LDAP server.

An internal error occurred.

An encode error occurred.

A decode error occurred.

The connection has timed out.

The supported SASL does not match the LDAP server side.

The searching filter is invalid.

Cancelled by the user.

An internal parameter error occurred.

Failed to allocate memory.

Unable to connect to the LDAP server.

The supported LDAP version does not match the LDAP server side.

The LDAP function did not find the specified control.

The result is not included in the message.

Additional results are to be returned.

Client loop was detected.

The referral limit was exceeded.

Failed to resolve the LDAP server name using the DNS server.

The certificate of the LDAP server has expired.

Mutual authentication using GSS-SPNEGO (Kerberos v5) failed.

The search result remains.

The process is cancelled by a device reset.

The CN field of the LDAP server certificate does not match the server address.

The LDAP server certificate does not have the expected usage for a server.

The LDAP server certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The LDAP server certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the LDAP server certificate is invalid.

The hard disk has not been set.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification/management module.

The device certificate does not exist.

No certificate is sent from the communications peer.

Failed in authentication using a PKI card (PKI token).

The ticket certificate has expired.

The ticket certificate does not have the expected usage for a server.

The ticket certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The ticket certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the ticket certificate is invalid.

The hard disk has not been set.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification/management module.

Reception (E-mail/Internet FAX/IP Address FAX)

Failed to receive message.

A receiving request has been blocked because E-mails are currently being received.

Failed to log in to the E-mail server.

An internal error occurred.

Failed to connect to the server.

The connection has timed out.

Decoding failed due to invalid MIME format or S/MIME format.

Failed to allocate memory.

Job ID is invalid.

Failed to delete an E-mail message.

The mail box is full.

Failed to search the certificate.

Failed to retrieve the device certificate or private key.

An I/O error occurred.

A hard disk operation error has occurred, or memory capacity of the computer may be insufficient.

The S/MIME function is disabled.

The hard disk is invalid.

The format of the certificate from the E-mail sender is invalid.

The certificate has expired, or the validity period has not yet started.

The CN field of the certificate does not match the server address.

The certificate does not have the expected usage.

The certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the certificate is invalid.

Failed to initialize the certificate verification.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification.

The device certificate does not exist.

No certificate is sent from the server.

FTP Transmission

The network connection is busy.

Parameter error (e.g. the file name is NULL).

Parameter is invalid.

The specified protocol is unavailable.

The device is not connected to the network.

The process is cancelled by a device reset.

Failed to allocate memory.

The FTP connection is already open.

Failed to connect to the server.

The connection has timed out.

The connection has been interrupted.

The file has not been deleted.

The file transfer failed (e.g. due to insufficient server capacity).

The file transfer failed (e.g. due to insufficient server capacity).

Incorrect login name or password.

The specified folder does not exist.

The file operation failed (e.g. due to insufficient server capacity).

Failed to create a folder.

SMB Send

Operation failed because a connection is closed.

The network connection is busy.

The protocol is not initialized.

The device is not connected to the network.

The connection has been interrupted.

The network is reset during forwarding.

An I/O buffer capacity shortage occurred.

Failed to connect to the server.

The host name is not specified.

The specified host name does not exist on the network.

The user name is not specified.

Unable to log in with the specified user name and password.

The user does not have write permission to the folder.

Failed to log in due to an SMB protocol error.

The folder name is not specified.

The specified folder does not exist.

The user name is not specified.

Unable to log in with the specified user name and password.

The user does not have write permission to the folder.

Failed to log in due to an SMB protocol error.

The specified file name is invalid.

Failed in authentication using a PKI card (PKI token).

The certificate has expired, or the validity period has not yet started.

The purpose of the certificate is not right.

CA that cannot be trusted or is not registered.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

The size of the expiration list is too large.

Failed in initialization of the certificate verification.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification.

The device certificate does not exist.

No certificate is sent from the server.

Library internal error (Parameter error)

SMB signature verification error

Failed to connect to the server.

DFS resolution error

Failed to log in.

Читайте также:  The following messages have been blocked by your administrator due to validation error

Failed due to a library internal error (insufficient memory).

The folder path is invalid.

Host name resolution error

The user name is not specified.

Could not log in using the specified user name and password.

The user failed to log in because an error has occurred in the SMB protocol that has no write permissions to the folder.

Failed due to a library internal error (insufficient memory).

Packet format error

The access is rejected.

The shared path for the destination is incorrect.

The file is locked.

The requested file is not a directory.

The specified name is invalid.

The directory is not empty.

Cannot overwrite data because a file or folder of the same name exists.

Operation timeout error

You have requested an unsupported function. Otherwise, an unsupported function has been requested.

No write attributes are assigned to the file.

Library internal error (Parameter error)

The user does not have write permission to the folder.

The access is rejected.

Transmission(E-mail/Internet FAX/IP Address FAX)

The network connection is busy.

The file size is too large.

Insufficient memory of the device.

The pipe is broken.

The specified protocol is unavailable.

The device is not connected to the network.

Unable to reach the destination network.

The connection aborted by the network.

A buffer shortage occurred.

No connection exists with the client.

The connection has been interrupted.

The operation has timed out.

The connection is rejected.

The host is shut down.

SMTP server error. Since the service is unavailable, the transfer channel is closed.

SMTP server error.

The password must be changed.

SMTP server error.

Unable to access to the mail box.

SMTP server error.

The requested action has been cancelled because an error occurred while processing a job.

SMTP server error.

Shortage of the system storage capacity.

SMTP server error.

No E-mail massage.

SMTP server error.

Temporary authentication failure.

SMTP server error.

Unable to queue a message to the node.

SMTP server error.

The node is not permitted.

SMTP server error.

An unsupported SMTP error code of 400s is received from the SMTP server.

SMTP server error.

Syntax error (command unrecognized).

SMTP server error.

Syntax error in parameters or arguments.

SMTP server error.

The command is not implemented.

SMTP server error.

Bad sequence of commands.

SMTP server error.

The command parameter is not implemented.

SMTP server error.

The server does not receive mail.

SMTP server error.

The access is rejected.

SMTP server error.

The authentication mechanism is too weak.

SMTP server error.

SMTP server error.

The requested authentication mechanism requires encryption.

SMTP server error.

The requested action is not executed.

SMTP server error.

The user is not connected locally.

SMTP server error.

The requested E-mail action is cancelled.

SMTP server error.

The requested action is not accepted.

An SMTP server error, or an internal error when sending data.

The transaction failed.

SMTP server error.

MAIL/RCPT parameter error.

SMTP server error.

An unsupported SMTP error code of 500s is received from the SMTP server.

The certificate has expired, or the validity period has not yet started.

The CN field of the certificate does not match the server address.

The certificate does not have the expected usage.

The certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the certificate is invalid.

Failed to initialize the certificate verification.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification.

The device certificate does not exist.

No certificate is sent from the server.

An unexpected error occurred.

An unexpected error occurred within the library being used.

An invalid channel is specified.

SMTP server address is invalid.

Parameter error (MIMEBodyHeader).

Parameter error (DisplayName).

Parameter error (character set).

Parameter error (From address).

Parameter error (To address).

Parameter error (CC address).

Parameter error (BCC address).

Parameter error (EmailSet is NULL).

Parameter error (destination certificate is NULL).

Parameter error (E-mail body).

The hard disk is invalid.

The S/MIME function is disabled.

Self-certificate error. The device certificate cannot be used in the S/MIME function. One possibility, among others, is that the type of encryption key is not RSA.

An invalid encryption algorithm is specified.

An invalid signature algorithm is specified.

The E-mail address included in the destination certificate does not match the destination address (To/Cc/Bcc).

The E-mail address included in the certificate does not match the sender (From) address.

Format error of the certificate.

Parameter error (Disposition-Notification-To).

Message syntax error of the receiver side.

The SMTP server does not support the STARTTLS command.

PKI card access error.

Parameter error (SMTP authentication method)

Parameter error (PIN code)

Failed to retrieve a ticket.

Failed in authentication using a PKI card (PKI token).

The validity period of the server certificate is invalid.

The certificate does not have the usage expected as a server.

The certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the certificate is invalid.

Although the environment is configured to use the hard disk, it is unable to perform verification because the hard disk path has not been specified.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification/management module.

WebDAV Transmission

The network connection is busy.

The format of the URL of the target resource is invalid. Parameter error.

Attempted to send data that exceeds the maximum transferrable size for transfer coding.

WebDAV send is disabled.

The device is not connected to the network.

The process is cancelled by a device reset.

A buffer shortage occurred.

The connection has already been established.

The connection to the WebDAV server failed (including connection time out).

The connection has been interrupted with the condition that is insufficient to the specified size.

Proxy authentication error.

The server does not support WebDAV.

Unable to upload data to the server.

The intermediate resource is not a collection (directory) (e.g. the specified folder does not exist).

The target resource is a collection (directory).

Although «https» is specified for the resource URL, the connection is interrupted because the WebDAV server certificate has expired.

The CONNECT method is issued to the proxy server to establish an SSL connection via a proxy, but it is rejected.

A communication error occurred while sending a request.

A communication error occurred while receiving a response.

The transfer size exceeds the maximum allowance.

Although use of a proxy has been specified, the proxy setting information is unavailable.

The connection to the proxy server failed (including connection time out).

Failed to retrieve a ticket.

Failed in chunk TX to SharePoint Server.

Another internal error occurred (e.g. memory shortage).

The certificate has expired, or the validity period has not yet started.

The CN field of the certificate does not match the server address.

The certificate does not have the expected usage.

The certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the certificate is invalid.

Failed to initialize the certificate verification.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification.

Читайте также:  From read error war thunder

The device certificate does not exist.

No certificate is sent from the server.

Failed in authentication using a PKI card (PKI token).

The validity period of the server certificate is invalid.

The certificate does not have the usage expected as a server.

The certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the certificate is invalid.

Although the environment is configured to use the hard disk, it is unable to perform verification because the hard disk path has not been specified.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification/management module.

SMB Browsing

Operation failed because a connection is closed.

The connection has been interrupted.

The specified protocol is unavailable.

The device is not connected to the network.

The internal channel detected an error immediately before establishing communication.

Failed to connect to the server.

The group name/host name is not specified.

The specified group name/host name does not exist on the network.

Other errors to which an error code is not assigned.

The browser machine (master browser/backup browser) is not found.

Unable to log in to the browser machine (master browser/backup browser).

The sub folder does not exist.

The request is not accepted due to an invalid call sequence etc.

The number of groups is too large.

The number of host PCs is too large.

The number of shared resources is too large.

Failed in authentication using a PKI card (PKI token).

The certificate has expired, or the validity period has not yet started.

The purpose of the certificate is not right.

CA that cannot be trusted or is not registered.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

The size of the expiration list is too large.

Failed in initialization of certificate verification (The path of the hard disk for saving certificates is not specified).

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification.

The device certificate does not exist.

No certificate is sent from the server.

Library internal error (Parameter error)

SMB signature verification error

Failed to connect to the server.

DFS resolution error

Failed due to a library internal error (insufficient memory).

The folder path is invalid.

Host name resolution error

The user name is not specified.

Could not log in using the specified user name and password.

The user failed to log in because an error has occurred in the SMB protocol that has no write permissions to the folder.

Failed due to a library internal error (insufficient memory).

Packet format error

The shared path for the destination is incorrect.

The file is locked.

Operation timeout error

You have requested an unsupported function. Otherwise, an unsupported function has been requested.

No write attributes are assigned to the file.

Library internal error (Parameter error)

The user does not have write permission to the folder.

The access is rejected.

User Authentication

Invalid parameter (e.g. the number of characters exceeds the limit, blank).

The authentication function setting is disabled.

Failed to resolve the name using the DNS server.

Unable to find the authentication server.

Failed to authenticate.

Failed to allocate memory.

An unexpected error occurred.

An authentication request is received while an internal task of the user authentication client is being performed.

The network was reset during user authentication.

Failed to allocate memory.

Time out occurred.

Failed in authentication using a PKI card (PKI token).

The SSL certificate has expired.

The certificate does not have the expected usage.

The certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the certificate is invalid.

The hard disk has not been set.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification.

WebDAV Client/Remote Panel

The ID of a client that is not active is specified.

(Response reception) Receive time out occurred.

(Request transmission) An invalid request method is specified.

(Response reception) A receive error occurred. Or an invalid request URL is specified.

(Request transmission) An invalid request URL is specified.

(Response reception) The size of the content length or the receive size exceeds the maximum transferable size. Or the size of the message body is too large.

(Request transmission) The size of the message body is too large.

(Response reception) The process is cancelled by a device reset. Or the size of the message body exceeds the maximum transferable size.

(Request transmission) The size of the message body exceeds the maximum transferable size.

(Response reception) An internal error occurred. Or the process is cancelled by an internal reset.

(Request transmission) The process is cancelled by an internal reset.

Failed to connect to the WebDAV server.

An error occurred while sending data to the WebDAV server.

A timeout occurred while sending data to the WebDAV server.

Failed to connect to the proxy server.

The proxy server rejected the connection request.

While the proxy server specification is valid, the host of the proxy server is not specified.

Failed to authenticate the proxy server.

Other error was returned from the proxy server.

An internal error occurred.

The process is cancelled because MIO_REQBODY_ERROR is specified by the device application.

An invalid PIN code is specified.

Failed to retrieve a ticket.

The internally specified parameter is invalid.

The certificate has expired, or the validity period has not yet started.

The CN field of the certificate does not match the server address.

The certificate does not have the expected usage.

The certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the certificate is invalid.

Failed to initialize the certificate verification.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification.

The device certificate does not exist.

No certificate is sent from the server.

Failed in authentication using a PKI card (PKI token).

The validity period of the server certificate is invalid.

The certificate does not have the usage expected as a server.

The certificate is not trusted. To trust the certificate, the certificate must be registered to the system.

The certificate has expired.

The CA server rejected the connection.

The connection to the server that checks for expiration of the certificate has timed out.

Unable to check for expiration because the CRL size exceeds the maximum capacity that can be retained (1MB).

The format of the certificate is invalid.

Although the environment is configured to use the hard disk, it is unable to perform verification because the hard disk path has not been specified.

Unable to perform verification because there are too many certificates to be verified (the maximum number of certificates that can be verified at a time is 20).

Internal error of the certificate verification/management module.

Источник

Оцените статью
toolgir.ru
Adblock
detector