Write error sorry no info avail



Проблема с прошивкой, пишет: avrdude: ser_recv(): read error: Неверный дескриптор.

Доброго времени суток, столкнулся с проблемой при залитии прошивки на принтер.

avrdude: ser_recv(): read error: Неверный дескриптор.

После повторной попытки залить (‘а вдруг’,- подумал я) написал мне на красненьком вот так:

avrdude: ser_send():write error: sorry no info avail

Полностью сообщение об ошибке выглядит так:

Arduino: 1.8.2 (Windows 8.1), Плата:’Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)’

Скетч использует 101244 байт (39%) памяти устройства. Всего доступно 253952 байт.

Глобальные переменные используют 4450 байт (54%) динамической памяти, оставляя 3742 байт для локальных переменных. Максимум: 8192 байт.

avrdude: ser_open(): can’t open device ‘\.COM1’: Не удается найти указанный файл.

avrdude: ser_drain(): read error: Неверный дескриптор.

avrdude: ser_send(): write error: sorry no info avail

avrdude: stk500_send(): failed to send command to serial port

avrdude: ser_recv(): read error: Неверный дескриптор.

avrdude: stk500v2_ReceiveMessage(): timeout

avrdude: ser_send(): write error: sorry no info avail

avrdude: stk500_send(): failed to send command to serial port

avrdude: ser_recv(): read error: Неверный дескриптор.

avrdude: stk500v2_ReceiveMessage(): timeout

avrdude: ser_send(): write error: sorry no info avail

avrdude: stk500_send(): failed to send command to serial port

avrdude: ser_recv(): read error: Неверный дескриптор.

avrdude: stk500v2_ReceiveMessage(): timeout

avrdude: ser_send(): write error: sorry no info avail

avrdude: stk500_send(): failed to send command to serial port

avrdude: ser_send(): write error: sorry no info avail

avrdude: ser_recv(): read error: Неверный дескриптор.

avrdude: stk500v2_ReceiveMessage(): timeout

avrdude: ser_send(): write error: sorry no info avail

avrdude: stk500_send(): failed to send command to serial port

avrdude: ser_recv(): read error: Неверный дескриптор.

avrdude: stk500v2_ReceiveMessage(): timeout

avrdude: ser_send(): write error: sorry no info avail

avrdude: stk500_send(): failed to send command to serial port

avrdude: ser_recv(): read error: Неверный дескриптор.

avrdude: stk500v2_ReceiveMessage(): timeout

avrdude: stk500v2_getsync(): timeout communicating with programmer

Этот отчёт будет иметь больше информации с

включенной опцией Файл -> Настройки ->

‘Показать подробный вывод во время компиляции’

Это моё первое знакомство с 3д принтером, так что если знаете решение проблемы, то распишите пожалуйста подробнее, чтобы до ‘чайника’ дошло.

Источник

SparkFun Forums

Where electronics enthusiasts find answers.

Pro Micro: avrdude: ser_send(): write error: sorry no info

Pro Micro: avrdude: ser_send(): write error: sorry no info #142730

I can’t get the board to program.

I am running Windows XP, I have loaded the driver and it sees the board, I have loaded promicro-arduino.zip and installed the files.
I have the arduino directory in my programfiles directory and have changed the properties to reflect the new location.

I can select the Pro Micro (I am using the 5V board) and the correct com port, but nothing I do gets me anything except the «write error» message.
I do see the orange LED blink twice when it tries to program but that’s all.

I tried «lenoardo» fix and have selected every programmer on the list.

What am I doing wrong?

User mini profile

    Posts: 1 Joined: Wed Apr 11, 2012 4:41 pm Status: Off-line

Re: Pro Micro: avrdude: ser_send(): write error: sorry no i #146335

I also receive this error but on Win 7 64x with arduino 1.01. I’ve tried everything! Following the «getting started» guide for the micro went smooth, everything seemed normal until I was asked to upload the modified Blink example, then it simply timed out and never finished uploading — Then this error pops up.

Читайте также:  Kraftool 34760 error 5

What could cause this?

User mini profile

deuplonicus

    Posts: 1 Joined: Wed Jun 20, 2012 6:21 am Status: Off-line

Re: Pro Micro: avrdude: ser_send(): write error: sorry no i #146457

deuplonicus wrote: I also receive this error but on Win 7 64x with arduino 1.01. I’ve tried everything! Following the «getting started» guide for the micro went smooth, everything seemed normal until I was asked to upload the modified Blink example, then it simply timed out and never finished uploading — Then this error pops up.

What could cause this?

I’m not sure if your problem is directly related to the first post. I’m having this same problem with Arduino 1.0.1 and some older Pro Micro. I’m guessing the older Pro Micro’s with the older bootloaders (before June 19 2012) aren’t compatible with the new Pro Micro Addon zip (that gets extracted to the Arduino/hardware folder). For now I can still upload sketches to my Pro Micro’s using Arduino 1.0. Hopefully a fix for 1.0.1 comes out soon.

When trying to upload using 1.0.1 (having extracted the Addon zip, restarted Arduino IDE and selecting the Sparkfun Pro Micro 5V/16MHz) I get these errors after the Rx and Tx LED’s flash for a while.

Источник

AdaWiki

User Tools

Site Tools

Table of Contents

While Arduino is a nice little system, there’s a lot of bugs. Hopefully they’ll be fixed soon, but until then, here’s problems you’re likely to run into.

I’m using Vista and.

Sorry pal, but Arduino and the avr-gcc/avrdude backend are pretty much not Vista-ready. Try XP/2000 which is much more likely to work!

**avrdude: stk500_getsync(): not in sync: resp=0x00**

If you get the following error message «avrdude: stk500_getsync(): not in sync: resp=0x00″ that means that the Arduino is not responding. There are literally dozens of reasons this could be.

Check the following:

Note that it is nearly impossible for anyone to debug this, as there are so many possible issues. Try everything.

**java.lang.NullPointerException at processing.app.Serial.setDTR**

If you get the following error message java.lang.NullPointerException at processing.app.Serial.setDTR(Serial.java:480)

It means you dont have a serial port selected, go back and verify that the correct driver is installed (lesson 0)and that you have the correct serial port selected in the menu.

This is a bug in Arduino and will hopefully be fixed in v10.

**avrdude: Expected signature for ATMEGA is . **

If you get the following error avrdude: Expected signature for ATMEGA is …

Then you have either the incorrect chip selected in the Tools menu or the wrong bootloader burned onto the chip

ser_send(): write error: sorry no info avail

(no screenshot as I can’t reproduce it)

Читайте также:  Ren py script error

You have the wrong serial port selected. Make sure the driver is installed and you have the correct serial port number, see lesson 0.

avrdude: can’t open device «COM10»: The system cannot find the file specified

If you get the following error: avrdude: can’t open device «COM10»: The system cannot find the file specified (under Windows, COM port value may vary)

It means that you have too many COM ports. Say maybe you’ve got 9 Arduinos, each one has a unique serial number so when it’s plugged in it gets its own COM port. However that COM port sits around even when the Arduinos are not plugged in. Thus every time you plug in a new USB-serial device the COM number goes up and up until its too high.

You should make sure that the port is numbered as low as possible. You can use a program like FTClean to clear out old COM ports you aren’t using anymore. Once you’ve cleaned out the ports, you’ll have to reinstall the driver again (see lesson 0).
Alternately, if you’re sure that the ports are not used for something else but are left over from other USB devices, you can simply change the COM port using the Device Manager. Select the USB device in the Device Manager, right click and select Properties

Then click Advanced… and in the next window change the COM port to something like COM4 or COM5.

Don’t forget to select the new port name in the Arduino software. The lower port names may say (in use) but as long as the other USB devices aren’t plugged in, it shouldn’t be a problem using them. This is a little riskier than just using FTClean…so I’d go for that first.

This is a bug in Arduino and will hopefully be fixed in v10.

Источник

Arduino.ru

Регистрация новых пользователей и создание новых тем теперь только на новом форуме https://forum.arduino.ru

forum.arduino.ru

Скетч не загружается в arduino nano

Имеется 2-ве Arduino nano и Bluetooth модуль HC-06.

Сначала припаял HC-06 к первой ардуино(которая только пришла) и сразу залил такой скетч:

Этот скетч не залился и после него никакие скетчи больше не загружаются. Выдает ошибку:

Причем «resp=0x90» изначально был «resp=0xd4» (по-моему). Потом чередовались ошибки: сначала «resp=0xe0″(тут тоже точно не помню), потом «resp=0x00».

Почитал на разных форумах, что за ошибка. Попробовал все советы, кроме перепрошивки — ничего не помогает.

Подумал, что arduino пришла бракованная, поэтому решил проверить на второй arduino, которая у меня уже давно и всегда хорошо работала.

Загрузил на вторую ардуину такой скетч:

Все прекрасно заработало, поэтому решил залить скетч, который загрузил в первую ардуину и произошло все то же самое, что и с первой ардуиной — то есть скетчи перестали загружаться и в эту ардуину.

Причем загрузка идет бесконечно и не выдает никакой ошибки пока не нажмешь на «Reset» на самом МК или не выдернешь USB. И, кстати, скетч, который был залит изначально (рабочий), до сих пор работает.

Читайте также:  What is error 503 guru meditation

Я так понял, что ошибка в том, что я объявил переменную «val», как char, а Serial.read() принимает байты.

Подскажите, пожалуйста, как это исправить без перепрошивки МК.

У меня имеется третья рабочая arduino nano, но она уже используется в другом проекте и нет никакого желания все отпаивать от нее и потом заного припаивать.

Источник

Error opening serial port and can’t upload sketch #9386

Comments

dancind commented Nov 1, 2019

Hello, I am attempting to do my first project and I seem to already be running into problems. I was following a tutorial and was told to click the Serial Monitor button. When I do so, I receive the following error:

Arduino: 1.8.10 (Windows 10), Board: «Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)»

Error opening serial port ‘COM3’. (Port busy)

I decided to truck ahead and try to upload a sketch and got a much more substantial error. Here is what that one said:

Arduino: 1.8.10 (Windows 10), Board: «Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)»

Sketch uses 1448 bytes (0%) of program storage space. Maximum is 253952 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 8183 bytes for local variables. Maximum is 8192 bytes.
avrdude: ser_open(): can’t open device «\.\COM3»: Access is denied.

avrdude: ser_drain(): read error: The handle is invalid.

avrdude: ser_send(): write error: sorry no info avail
avrdude: stk500_send(): failed to send command to serial port
avrdude: ser_recv(): read error: The handle is invalid.

avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: ser_send(): write error: sorry no info avail
avrdude: stk500_send(): failed to send command to serial port
avrdude: ser_recv(): read error: The handle is invalid.

avrdude: ser_recv(): read error: The handle is invalid.

avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: ser_send(): write error: sorry no info avail
avrdude: stk500_send(): failed to send command to serial port
avrdude: ser_recv(): read error: The handle is invalid.

avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: ser_send(): write error: sorry no info avail
avrdude: stk500_send(): failed to send command to serial port
avrdude: ser_recv(): read error: The handle is invalid.

avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: ser_send(): write error: sorry no info avail
avrdude: stk500_send(): failed to send command to serial port
avrdude: ser_recv(): read error: The handle is invalid.

avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: ser_send(): write error: sorry no info avail
avrdude: stk500_send(): failed to send command to serial port
avrdude: ser_recv(): read error: The handle is invalid.

avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_getsync(): timeout communicating with programmer

As I said before, this is my first project with an Arduino ever, so if there is more information I can provide, I would be glad to provide it. I am having a heck of a time with this and I am sure it is because I am doing something wrong.

Thank you for your help.
Dylan Fleming

The text was updated successfully, but these errors were encountered:

Источник

Оцените статью
toolgir.ru
Adblock
detector